• LED Light Units
• Power Supply Units
• Cables
• Options
• Lens

• Lineup
• PD2 Series [for 12V Light Units]

This Digital Power Supply Unit can be connected to a 12V LED Light Unit with a total power consumption of up to 46W. It operates on a 100 to 240V AC input. It has a measures 62 x 230 x 110mm (width x depth x height).

Download drawing files(PDF/DXF) from Here.

Direct Number	2000536
Lighting Method	Constant lighting
Drive Method	Constant-voltage system
Light Control Method	PWM control
No. of Channels	1Channel
Applicable Light Units	12V / 46W
PWM Frequency	62.5KHz
Light Control (Manual)	Use of the intensity control knobs on the front panel (Coarse, Fine) (Each 16 steps)
Light Control (Remote)	Input in negative logic (B0 to B7), Manual / External control (NT/EXT), The write bit (WR), Lighting ON/OFF (ON)
Error Detection Display	The Error indicator lamp on the front panel is lit when overcurrent is detected
Error Detection Output	External control connector 14 pin (OCP) : Open collector ON when overcurrent is detected
Over Current Protection	Operates at 107% min. Automatically reset, or manually reset by turning power OFF then ON again.
Input Voltage (rating)	100 to 240V AC
Power Consumption (typ.)	122VA
Frequency	50 / 60Hz
Inrush Current (typ.)	15A (at 100V AC) Note : From a cold start
Output Voltage (rating)	12V DC
Output Current (rating)	3.8A
External Control (input)	Insulation : Non-insulated with power supply for illuminator. Circuit : Internally pulling up to +5V power supply by resistance (4.7kΩ) HS-CMOS input
Output Connector	SMP-02V-BC [1 : Output (+) / 2 : Output (-)] x 2Piece SMP-04V-BC [1 : NC / 2 : Output (+) / 3 : Output (-) / 4 : Fan (GND)] x 1Piece
External Control Connector	Manual ON/OFF control : Phone jack (Φ3.5) x 1Piece External control : 15-pin D-sub plug with M2.6mm screws x 1Piece
Cooling Method	Forced air cooling
Material	Steel plate t1.0
Operating Temperature and Humidity	Temperature : 0 to 40ºC, Humidity : 20 to 85%RH (No condensation)
Storage Temperature and Humidity	Temperature : -20 to 60ºC, Humidity : 20 to 85%RH (No condensation)
Dimensions	W 62mm x D 230mm x H 110mm
Weight	1300g
Accessories	2m long 3-prong AC power cord with ground terminal x 1, Instruction Guide x 1, Optional Cable Operation Guide x 1
Cable	EXCB2 Series (External Control Cables) NFCB2 Series (External Control Cables)
Option	STU-3000 (Strobe Unit)

Note: Select a model after making sure that the total power consumption of the Light Unit is within the output power capacity of the Power Supply Unit to which it will be connected.

Ctalog	C_PowerSupply_PD2_e.pdf(PDF:3MB)
PDF Drawing	PD2-5012(A)_e.pdf(PDF:167KB)
DXF Drawing	PD2-5012(A)_e.dxf(DXF:221KB)
User Manual	M_PD2_1ch_e.pdf(PDF:687KB)
User Manual	M_Cable_e.pdf(PDF:1138KB)
3D-CAD	Click to open download page for 3D-CAD.

Note: You must log in from the Login Form to be able to download data that is available only to members of this website.
You can register from here if you are not a CCS member.
Quick Start Guide for downloading 3D CAD data.